Gyeon Q² Mohs EVO is a state of the art quartz coating that showcases the latest advances in low volatile silicon (Si) technology. If, like us, you always question relative performance in the world of car care, then you're probably wondering how Gyeon Q² Mohs EVO differs to rival products, and what it offers that they don't? The answers to these questions stem back to its unique alcohol-free formula, which lays down a hybrid film of organic-silica that increases in molecular weight as it cures, forming a pore-free organic-silica nano-composite. None of the other SiO2-based coatings we stock work in the same way; they lay down glass-like coatings that form strong molecular bonds and, in some cases, fully crystallized lattices, but none are as structurally dense (and thus as resistant to physical and chemical attack) as Gyeon Q² Mohs EVO. This is supported by the fact that each layer of Gyeon Q² Mohs EVO shrinks by less than 5% as it cures, whereas the average figure for other SiO2-based coatings is 30%.
Now that we have confirmed how Gyeon Q² Mohs EVO differs to rival products, we can look at the benefits it offers. Firstly, because it contains no alcohol, it doesn't flash off rapidly upon contact, which makes it easier to apply. Secondly, because it forms a pore-free composite as it cures, it produces a substantially harder and more durable coating than rival products. We've tested this by subjecting Gyeon Q² Mohs to a brutal decontamination test, in which selected panels were: (i) treated with a spirit-based tar remover; (ii) treated with a strong acid-based fallout remover; (iii) clayed with a mild clay bar, and; (iv) treated with neat isopropyl alcohol. The net effect of this treatment was negligible; the panels were left beading just as strongly as the day the Gyeon Q² Mohs was first applied. Furthermore, in a long-term test on a daily driver, we observed clear signs of functioning protection through to the two year mark, which places Gyeon Q² Mohs EVO in a league of its own in terms of durability.
As a result of being coated with an ultra-smooth, extremely dense layer of this organic-silica nano-composite, treated surfaces become hydrophobic (water-hating), which causes rainfall and rinse water to bead up and roll off very quickly. This beading action not only looks good, but also tends to pick up and carry away fresh contaminants, which, combined with the naturally high scratch resistance of the coating, makes routine washing easier and much safer. In addition to this strong self-cleaning effect, Gyeon Q² Mohs also provides excellent protection against bird droppings, bug splatter, road salt and harmful UV radiation for up to two years at a time, even on daily drivers (it is impervious to cleaning chemicals and pressure washing, and once fully cured can only be removed by machine polishing). Gyeon Q² Mohs EVO is currently supplied as a pre-packed kit containing either a 30 ml or 50 ml bottle of Gyeon Q² Mohs EVO, a 100 ml bottle of Gyeon Q²M Cure, a Gyeon Q²M Applicator Block, four Gyeon Q²M Applicator Suedes and an instruction booklet.
|By hand only
|36 months +
|Emits Strong Fumes
|Yes (allow 1 hour between coats)
|All paint types and colours
How To Use
You should apply Gyeon Q² Mohs EVO in a dry place out of direct sunlight. In all cases, prepare the surfaces you are going to treat in the normal way (wash > decontaminate > polish), and then do a wipe down with Gyeon Q²M Prep to ensure that they are spotlessly clean. Next, using the supplied dropping pipette, lightly wet one of the supplied Gyeon Q²M Applicator Suedes with Gyeon Q² Mohs EVO, wrap it around the supplied Gyeon Q²M Applicator Block and begin wiping it evenly on to the first panel, using light pressure and overlapping strokes. You should aim to treat no more than a single panel at a time, because after an initial volatilization period of 1-2 minutes you must then buff off the (still wet) residue as quickly as possible, i.e. before it begins to harden. Buffing off is best accomplished with a PB Super Buffing Towel using moderate speed and pressure in order to fully remove the residue and reveal an intense streak-free shine. Using a bright light, check the panel carefully for any smears and remove them before moving on; failure to remove smears fully can result in them hardening to the point of being impossible to remove without machine polishing, so make sure you are thorough!
After all panels are treated wait for a minimum of an hour and then apply a second coat. The car must then be left in a dry place out of direct sunlight for a minimum of 24 hours to allow the layers to harden (if you wish, you can accelerate this process by heating the treated panels to 60°C for 10 minutes using an infra-red heat lamp). Finally, to reduce the risk of water spots forming while it continues to cure (full curing takes around 14 days to achieve), you should apply a final topcoat of Gyeon Q²M Cure (you should also avoid washing the car with any kind of detergent for 7 days following application). Please note that you must discard all used applicators and towels after you've applied each coat of Gyeon Q² Mohs EVO because it becomes extremely hard as it cures, forming a residue that has the potential to inflict severe marring or worse if applicators and towels are re-used. Furthermore, after each use you must also replace the dropping pipette with the air-tight cap, and wash out the pipette with hot running water. Failure to follow these steps will most likely result in any leftover product setting solid in the bottle and the dropping pipette, rendering them unusable in the future.