Skip to content
FREE UK Delivery on orders over £75*
FREE UK Delivery on orders over £75*

We Say

A proper cleaning snow foam, not just a blanket of white bubbles. CARPRO Lift gets to work on road film and stubborn dirt before your wash mitt goes anywhere near the paintwork.

There's no shortage of snow foams that look impressive when they're covering a car, but what really matters is how much dirt they remove before you start washing by hand. CARPRO Lift is designed with cleaning performance firmly in mind. Its alkaline formula tackles road grime, grease and the sort of stubborn traffic film that builds up during winter, helping remove a significant amount of contamination without physical contact.

One of Lift's strengths is its balance between foam coverage and cleaning action. It produces a generous layer of foam that stays on the surface long enough for the surfactants to work, but it isn't simply trying to create the thickest possible foam. As the bubbles break down, the cleaning solution continues to wet the surface and loosen dirt. That's exactly what we want from a dedicated pre-wash, particularly on cars that haven't been cleaned for a while.

Lift is an alkaline cleaner, so we'd approach it a little differently from a gentle maintenance foam. It's a good choice when stronger cleaning is needed, but we'd be more cautious on freshly waxed or sealed paintwork, especially at stronger dilutions. For the contact wash afterwards, CARPRO Reset makes an excellent partner. If you're looking for a product aimed specifically at intensive winter cleaning, it's also worth comparing Lift with our wider snow foam range.

Key Features

Cleaning Strength 10/10 (PolishedBliss comparison rating)
Foaminess 9/10 (PolishedBliss comparison rating)
Recommended Dosage 100ML (Typical foam lance mix)

Description

CARPRO Lift Snow Foam is a highly concentrated alkaline foaming pre-cleaner designed to remove road grime and accumulated surface contamination before contact washing. Its pH 12 cleaning formulation combines alkaline ingredients with an active blend of surfactants to loosen and lift dirt from vehicle surfaces.

Unlike products formulated primarily for maximum foam thickness, Lift is designed to provide effective wetting and cleaning action throughout the dwell period. The foam clings to the vehicle while its bubbles gradually break down, allowing the surfactants to penetrate and loosen deposits of traffic film, grease and road dirt. The solution is formulated to rinse away readily after treatment.

CARPRO recommends a typical dilution of 1:10, although the concentration can be adjusted depending on the desired foam consistency and cleaning requirements. A weaker solution produces a more flowing foam, while a stronger concentration produces denser coverage. Actual foam thickness and the concentration reaching the vehicle will also depend on the foam lance and pressure washer being used.

Lift is intended for application through compatible pressure washer foam lances. CARPRO describes a typical dwell period of approximately five minutes, during which the cleaner should remain wet on the surface. Once the product has been thoroughly rinsed away, the vehicle can be washed using a suitable shampoo such as CARPRO Reset.

Specification

More Information
Application Pressure washer foam lance
Chemical Basis Alkaline surfactant cleaner
Cleaning Strength
10
Dilution Typically 1:10
Foaminess
9
pH 12 (alkaline)
Recommended Dosage 100ml (typical foam lance mix)
Typical Dwell Approximately 5 minutes

How To Use

  1. Prepare the vehicle

    Ensure the vehicle is cool and out of direct sunlight. Remove heavy loose deposits where necessary and check the suitability of the cleaner for any sensitive finishes.

  2. Prepare the dilution

    Dilute CARPRO Lift with water in a compatible foam lance. CARPRO recommends a typical ratio of 1:10, meaning one part Lift to ten parts water. For example, mix 100ml of Lift with 1 litre of water. Adjust the concentration according to the foam consistency required and the performance of your equipment.

  3. Apply the foam

    Using the foam lance, distribute Lift evenly over the vehicle. Cover the contaminated exterior surfaces thoroughly, allowing the cleaning solution to remain in contact with the dirt.

  4. Allow to dwell

    Leave the foam to work for several minutes, typically around five minutes depending on conditions. As the foam begins to break down, its surfactants continue loosening grime. Do not allow the solution to dry on the surface.

  5. Rinse and wash

    Thoroughly rinse away the foam and loosened contamination using a pressure washer. Follow with a conventional contact wash using a suitable car shampoo such as CARPRO Reset, then rinse and dry the vehicle.

Safety Data

CARPRO Lift is a concentrated alkaline cleaning product. Avoid contact with skin and eyes, wear suitable chemical-resistant gloves and eye protection when handling the concentrate, and avoid inhaling spray mist.

Use only on cool, compatible surfaces and never allow the product to dry. Strong alkaline cleaners may affect some waxes, sealants and sensitive finishes, particularly at higher concentrations. Keep out of reach of children and follow the current product label and Safety Data Sheet for full hazard classifications, first-aid measures and handling requirements.

Customer Reviews