BASKET   :   CHECKOUT
spacer
Feefo Gold Trusted Merchant 2016

GYEON Q2 RIM

Click image to see larger view

GYEON Q2 RIM is an advanced quartz coating specifically formulated to withstand very high temperatures (up to 350°C) and aggressive cleaning chemicals, which makes it ideal for protecting wheels, brake calipers and exhaust tips. Developed in South Korea, GYEON Q2 RIM uses the latest in low volatile content silicon (Si) technology to lay down a film of siloxane polymers and heat resistant additives that condense rapidly to form a fully crystallized SiO2 coating that bonds to painted and bare metal surfaces at the molecular level. Unlike rival nanotechnology products, GYEON Q2 RIM contains no alcohol and therefore doesn't flash off rapidly, which makes the application process far easier. It is also completely resistant to all types of cleaning chemicals in the pH range 2 (highly acidic) to 11 (strongly alkaline), which means that more aggressive cleaners can be used safely when required, e.g. following track days or back road runs.

As a result of being coated with a smooth, dense layer of fully crystallized SiO2, treated surfaces become naturally water hating (hydrophobic), which causes rainfall and rinse water to bead up and roll off very quickly. This extreme beading not only looks good, but also tends to pick up and carry away fresh contaminants, which, combined with the naturally high scratch resistance of the coating, makes routine washing easier and safer as a result. In addition to these benefits, GYEON Q2 RIM also provides excellent protection against brake dust and road salt for up to twelve months at a time, even on high performance cars whose wheels and exhaust systems become extremely hot during use (it is virtually impervious to heat, cleaning chemicals and pressure washing, and once fully cured can only be removed by machine polishing). All said and done, it's by far the most effective and longest lasting wheel (and metal) sealant we currently use and stock.

This set comprises...


1 x GYEON Q2 RIM (30 ml)

1 x GYEON Q2M APPLICATOR Set

1 x 3M Disposable Respirator

1 x Instruction Manual

You should apply GYEON Q2 RIM in a dry place out of direct sunlight. In all cases, prepare the rims you are going to treat in the normal way (wash > decontaminate), and then do a wipe down with GYEON Q2M PREP to ensure that they are spotlessly clean. Next, using the supplied dropping pipette, lightly wet one of the supplied suede applicators with the product and begin wiping it evenly onto the first rim, using light pressure and overlapping strokes. You should aim to treat no more than one rim at a time, because after an initial volatilization period of 5-10 minutes you must then buff off the (still wet) residue as quickly as possible, i.e. before it dries out and begins to harden. Buffing off is best accomplished with a PB Utility Towel using moderate speed and pressure in order to fully remove the residue and reveal an intense streak-free shine. Using a bright light, check the rim carefully for any smears and remove them before moving on; failure to remove smears fully can result in them hardening to the point of being impossible to remove without machine polishing, so make sure you are thorough!

After all of the rims are treated, wait for a minimum of an hour and then apply a second coat. The rims must then be left somewhere warm and dry for a minimum of 24 hours to allow the SiO2 coating to harden (if you wish, you can accelerate this process by heating the treated rims to 60C for 10 minutes using an infra-red heat lamp). Finally, to reduce the risk of water spots forming while it continues to cure (full curing takes around 14 days to achieve), you should apply a protective top coat of GYEON Q2M CURE (you should also avoid washing the car with any kind of detergent for the first 7 days). Please note that you must discard all used applicators and towels after youve applied each coat, because GYEON Q2 RIM hardens massively as it cures, forming a residue that has the potential to inflict severe marring or worse if applicators and towels are re-used. Furthermore, after each use you must also replace the dropping pipette with the air-tight cap, and then wash out the pipette with hot water. Failure to follow these steps will result in any leftover product setting solid in the bottle and the pipette, rendering it unusable in the future.
Enhances gloss:Yes
Adds protection:Yes
Emits strong fumes:Yes
Application method:By hand only
Slickness:Slickness 4/5
Beading:Beading 5/5
Durability:9 months +
Recommended for:All wheel types & finishes, plus all bare metal surfaces
Q2 RIM - 30 ml Set
22.00
In Stock
QUANTITY 
Request a price match (terms apply)
View BasketCheckout Now
spacer
spacer